Étude et optimisation des interfaces fibre-matrice polymère de composites structuraux à base thermoplastique - TEL - Thèses en ligne Accéder directement au contenu
Thèse Année : 2018

Analysis and optimisation of fibre-matrix interface in thermoplastic polymer based composites

Étude et optimisation des interfaces fibre-matrice polymère de composites structuraux à base thermoplastique

Résumé

This work is devoted to the study and optimisation of glass/PA 6-6 interfacial properties for the conception of structural composite materials. A method to clean and reactivate glass surface was first developed. It allowed us to work with glass fibres and model substrates (glass plates), aiming to get controlled surfaces before the application of new coatings. Controlling the interface between the reinforcement and the matrix requires the optimisation of the sizing, which is mainly composed of film formers and coupling agents. This study consisted in the characterisation of thermal, mechanical and surface properties of the new coatings applied to the glass substrates. Different film former bases, selected for their compatibility with the processing conditions of PA 6-6, and two usual coupling agents were studied. This work allowed to identify different parameters that play a role in the improvement of interfacial properties. By working with a wide range of film formers, we could show that the use of a film former with close chemical composition from the matrix allows to reach better interfacial properties. Increasing the surface roughness of coatings also participates in this improvement. The grafting of coupling agents was more efficient after 150°C thermal treatment than 110°C, and a synergistic effect was obtained by their association to a film former. The use of film formers with high thermal resistance provided very interesting interfacial properties, also improved, for some, by the addition of silica nanoparticles. Finally, DCB mode I mechanical test was adapted to our system, allowing to estimate the fracture toughness of the glass/PA 6-6 interface which is a complementary result to the estimation of the adhesion force measured by pull-off and pull-out tests
Ces travaux de thèse portent sur l’étude et l’optimisation des propriétés interfaciales verre/PA 6-6 pour la conception de matériaux composites de structure. Une méthode visant à nettoyer et réactiver la surface du verre a dans un premier temps été développée. Elle permet de travailler avec des substrats de type fibres ou substrats modèles (plaques de verre) et d’obtenir des surfaces « contrôlées » avant l’application de nouveaux revêtements. La maîtrise de l’interface entre renfort et matrice nécessite l’optimisation de l’ensimage, dont les principaux constituants sont des agents filmogènes et des agents de couplage. Au cours de ce travail, nous avons donc étudié les propriétés thermiques, mécaniques et de surface des nouveaux revêtements appliqués sur les substrats de verre. Différents agents filmogènes, sélectionnés pour être compatibles avec les conditions de mise en oeuvre du PA 6-6, ainsi que deux agents de couplages usuels ont été étudiés. Par le choix d’une large gamme de familles d’agents filmogènes, nous avons montré que l’utilisation d’un agent filmogène de composition chimique proche de celle de la matrice permet d’atteindre de meilleures propriétés interfaciales. L’augmentation de la rugosité de surface du revêtement contribue également à cette amélioration. Le greffage des agents de couplage sur le verre s’est révélé bien plus efficace avec un traitement thermique à 150°C qu’à 110°C et un effet de synergie a pu être observé lors de leur association avec un agent filmogène. L’utilisation d’agents filmogènes à haute résistance thermique a permis d’obtenir des propriétés interfaciales très intéressantes, renforcées pour certains systèmes par l’ajout de nanoparticules. Enfin, afin d’accéder à une estimation de la ténacité de l’interface, un test de DCB en mode I a été adapté à notre problématique. Les résultats obtenus ont été complémentaires à ceux obtenus par les tests du plot et de la microgoutte
Fichier principal
Vignette du fichier
TH2018GABETYANN.pdf (13.73 Mo) Télécharger le fichier
Origine : Version validée par le jury (STAR)
Loading...

Dates et versions

tel-02073608 , version 1 (20-03-2019)

Identifiants

  • HAL Id : tel-02073608 , version 1

Citer

Yann Gabet. Étude et optimisation des interfaces fibre-matrice polymère de composites structuraux à base thermoplastique. Polymères. Université de Lyon, 2018. Français. ⟨NNT : 2018LYSE1244⟩. ⟨tel-02073608⟩
473 Consultations
365 Téléchargements

Partager

Gmail Facebook X LinkedIn More